Differences

This shows you the differences between two versions of the page.

--- amc2020:group_n:sn74hc595n [2020/07/18 19:36] – jonas001
+++ amc2020:group_n:sn74hc595n [2021/08/24 17:35] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
+<html>
+  <left>
+    <a href="https://wiki.eolab.de/doku.php?id=amc2020:group_n:start"; onmouseover="style.color='green'";>
+      <span style="color:#2E71B8"; onmouseover="style.color='green'"; onmouseout="style.color='#2E71B8'";>
+        &#8617 Back to the main page
+      </span>
+    </a>
+  </left>
+</html>
 ====== SN74HC595(N) Shift Register ======
@@ Line 52: / Line 62: @@
 | Operating Temperature  | -40 – 125 °C                 |
 | Power consumption      | 80 μA (max at 6V)            |
+Further information can be found in the {{https://www.ti.com/lit/ds/symlink/sn74hc595.pdf?ts=1595095743394&ref_url=https%253A%252F%252Fwww.google.de%252F|SN74HC595 datasheet}}.
 ^ **//Table 2 //** SN74HC595(N) pin overview and description  ^^^^
@@ Line 137: / Line 149: @@
 ===== 4.3 Combining the Sketches =====
-This code can be combined with the code from the DHT-22 and the DS18B20s. This way the sensors are only powered when they are supposed to measure and are switched off again afterwards.
+This code can be combined with the code from the DHT-22 and the DS18B20s such that the sensors are only powered when they are supposed to measure and are switched off again afterwards.
-The sensors and the shift register need to be connected like explained in their pages, respectively. Additionally, the VDD pin of the DHT-22 must be connected to QB of the shift register and the VDD of both DS18B20s must be connected to QC. Furthermore, if a red LED with a 330Ω resistor in series is connected to QA, it indicates when the sensors finish their measurements with a short blink.
+The sensors and the shift register need to be connected like explained in their pages, respectively. Additionally, the VDD pin of the DHT-22 must be connected to QB of the shift register and the VDD of both DS18B20s must be connected to QC. Furthermore, if a red LED with a 330Ω resistor in series is connected to QA, it indicates when the sensors finish their measurements with a short blink (figure 3).
+^{{:amc2020:group_n:esp32_all_sensors_breadboard.png?direct&800|Figure 3}}^
+|**//Figure 3//** ESP32 connected with DHT-22, DS18B20 and SN74HC595.|
 ==== 4.3.1 The Code combined ====
@@ Line 370: / Line 385: @@
 During this test, all sensors were in equilibrium, measuring the room temperature during a rather hot summer day, and all results are close together, indicating that the sensors are working properly.
+<html>
+  <center>
+    <span>
+    <a href="javascript:self.scrollTo(0,0)"; onmouseover="style.color='green'";>
+      <span style="color:#2E71B8"; onmouseover="style.color='green'"; onmouseout="style.color='#2E71B8'";>
+        Back to the top &#10548
+      </span>
+    </a>
+    </span>
+  </center>
+</html>